MAXTOR 81280A2, 81620A3, 81081A2, 82560A4, 82580A5, 82100A4, 83840A6,
83201A6, 84000A6, 84320A8, 85120A8
| Device Type |
Hard Drive |
| Interface |
EIDE |
| Size |
3.5 in. third height |
| View |
Bottom |
| DRIVE CONFIGURATION |
| Setting |
J48 |
J50 |
 Drive is master |
open |
closed |
| Drive is slave |
open |
open |
| Cable Select |
closed |
open |
| USER CONFIGURABLE SETTINGS |
| Function |
Label |
Position |
| Factory configured - do not alter. |
J42 |
unidentified |
| Factory configured - do not alter. |
J44 |
unidentified |
| 4092 Cylinder limitation disabled |
J46 |
open |
| 4092 Cylinder limitation enabled |
J46 |
closed |
| Note: If system hangs during boot, before accessing BIOS, or
during boot after BIOS SETUP has been run, close jumper J46 and run
"Max-Blast" software to complete hard drive installation. |
MAXTOR MX9217SSW
| Interface: |
SCA SCSI-2 wide |
| Size: |
3.5 in. third height |
| View: |
Bottom |
| CONNECTIONS |
| Purpose |
Location |
| LED |
J2/jumper 4 |
| Spindle sync |
J2/jumper 7 |
| DRIVE CONFIGURATION |
| SCSI Address |
J2/Jumper 9 |
J2/Jumper 10 |
J2/Jumper 11 |
J2/Jumper 12 |
| 0 |
open |
open |
open |
open |
| 1 |
open |
open |
open |
closed |
| 2 |
open |
open |
closed |
open |
| 3 |
open |
open |
closed |
closed |
| 4 |
open |
closed |
open |
open |
| 5 |
open |
closed |
open |
closed |
| 6 |
open |
closed |
closed |
open |
| 7 |
open |
closed |
closed |
closed |
| 8 |
closed |
open |
open |
open |
| 9 |
closed |
open |
open |
closed |
| 10 |
closed |
open |
closed |
open |
| 11 |
closed |
open |
closed |
closed |
| 12 |
closed |
closed |
open |
open |
| 13 |
closed |
closed |
open |
closed |
| 14 |
closed |
closed |
closed |
open |
| 15 |
closed |
closed |
closed |
closed |
| USER CONFIGURABLE SETTINGS |
| Function |
Location |
Setting |
| Write protect disabled |
J2/jumper 1 |
open |
| Write protect enabled |
J2/jumper 1 |
closed |
| SCSI mode is SCSI-2 (if SCSI 1/2 pin is active) |
J2/pins 1 & 3 |
open |
| SCSI mode is SCSI-1 (if SCSI 1/2 pin is
active) |
J2/pins 1 & 3 |
closed |
| SDTR message disabled (if SDTR function is
active) |
J2/jumper 3 |
open |
| SDTR message enabled (if SDTR function is
active) |
J2/jumper 3 |
closed |
| Unit attention enabled (if U/A function is
active) |
J2/jumper 3 |
open |
| Unit attention disabled (if U/A function is
active) |
J2/jumper 3 |
closed |
| Spindle motor starts on power-up |
J2/jumper 5 |
open |
| Spindle motor starts on command only |
J2/jumper 5 |
closed |
| Termination enabled |
J4/jumper 1 |
closed |
| Termination disabled |
J4/jumper 1 |
open |
| Factory configured - do not alter |
J4/jumper 2 |
unidentified |
| Factory configured - do not alter |
J4/jumper 3 |
unidentified |
| MISCELLANEOUS TECHNICAL NOTES |
| On models with SCA connector only passive termination is
available. |