Previous Table of Contents Next

 

QUANTUM SATURN VP31080, SATURN VP32170

Interface SCSI-2 Fast
Size 3.5 in. third height
View Bottom

DRIVE SELECTION
SCSI ID J3/Pins 1 & 2 J3/Pins 3 & 4 J3/Pins 5 & 6
     0 open open open
1 closed open open
     2 open closed open
     3 closed closed open
     4 open open closed
     5 closed open closed
     6 open closed closed
     7 closed closed closed

 
USER CONFIGURABLE SETTINGS
Function Label Position
Write Protect disabled J3/pins 17 & 18 open
Write Protect enabled J3/pins 17 & 18 closed
Active termination enabled J5/pins 1 & 2 closed
Active termination disabled J5/pins 1 & 2 open
TERMPWR supplied by drive to SCSI interface J5/pins 5 & 6 closed
TERMPWR not supplied by drive to SCSI interface J5/ pins 5 & 6 open

 
SPINDLE MOTOR SELECTION
Setting J3/pins 13 & 14
Spindle motor start delayed by 12 sec x drive ID closed
     Spindle motor starts on command only open

 

QUANTUM SATURN VP31080S, SATURN VP32170S

Interface SCSI-2
Size 3.5 in. third height
View Bottom

DRIVE SELECTION
SCSI ID J3/pins 1-2 J3/pins 3-4 J3/pins 5-6
     0 open open open
1 closed open open
     2 open closed open
     3 closed closed open
     4 open open closed
     5 closed open closed
     6 open closed closed
     7 closed closed closed

 
USER CONFIGURABLE SETTINGS
Function Label Position
Write Protect disabled J3/pins 17-18 open
     Write Protect enabled J3/pins 17-18 closed
Termination enabled J5/pins 1-2 closed
     Termination disabled J5/pins 1-2 open
Termination power enabled J5/Pins 3-4 closed
     Termination power disable J5/pins 3-4 open
Note: only the last drive in a series of SCSI devices must be terminated.
LEDs
Function Label Function Label
Busy LED LED1 Fault LED LED2

 
SPINDLE MOTOR SELECTION
Setting J3/pins 13-14
Spindle motor start on power up closed
     Spindle motor starts on command only open

 

QUANTUM SIROCCO 1700AT, 2550AT

Interface ATA-2
Size 3.5 in. third height
View Bottom

DRIVE CONFIGURATION
Setting CS DS SP pin 28
Drive in master in a two drive system open closed open N/A
     Drive in a master in a two drive system closed open open ground
     Drive is master when slave does not use DASP signal closed open closed ground
     Drive is master when slave does not use DASP signal open closed closed N/A
     Drive is slave in a two drive system closed open open high
     Drive is slave in a two drive system open open open N/A
Note: when using the cable select option (CS closed) a special cable must be used.

 
MISCELLANEOUS TECHNICAL NOTES
Jumper PK is for parking an unused shunt.

 

QUANTUM CAPELLA VP31110, VP31110S, VP32210, VP32210S

Interface: SCSI-2 Fast
Size: 3.5 in. half height
View: Bottom

USER CONFIGURABLE SETTINGS
Function Location Setting
TRMPWR supplied by drive to SCSI bus J4 closed
TRMPWR is not supplied by drive to SCSI bus J4 open
Spindle motor starts on power-up with delay of SCSI ID x 12 sec. J3/jumper 7 closed
Spindle motor starts on command only J3/jumper 7 open
Drive is first or last drive in chain terminators installed
Drive is not first or last drive in chain terminators removed
Note: jumpers not mentioned in this document are unidentified.

 
DRIVE SELECTION - J3
Drive ID Jumper 1 Jumper 2 Jumper 3
0 open open open
1 closed open open
2 open closed open
3 closed closed open
4 open open closed
5 closed open closed
6 open closed closed
7 closed closed closed

 
CONNECTIONS
Function Location
Remote Busy LED J3/pins 11 & 9
Remote Fault LED J3/pins 11 & 7

 
Previous Table of Contents Next